Ruijie RG-AP180(V3) Wi-Fi 6 Access Point

●     Radio 1 – 2.4 GHz: 2×2 MIMO, two spatial streams

●     Radio 2 – 5 GHz: 2×2 MIMO, two spatial streams

Channels:

●     Radio 1 – 2.4 GHz: 20 MHz and 40 MHz

●     Radio 2 – 5 GHz: 20 MHz and 40 MHz

Combined peak data rate: 600 Mbps

●     Radio 1 – 2.4 GHz: 6.5 Mbps to 300 Mbps (MCS0 to MCS15 )

●     Radio 2 – 5 GHz: 6.5 Mbps to 300 Mbps (MCS0 to MCS15)

Radio technologies: Orthogonal Frequency-Division Multiplexing (OFDM)

Modulation types: BPSK, QPSK, 16-QAM, 64-QAM

Packet aggregation:

●     Aggregate MAC Protocol Data Unit (A-MPDU)

●     Aggregate MAC Service Data Unit (A-MSDU)

Dynamic Frequency Selection (DFS)

Cyclic Delay/Shift Diversity (CDD/CSD)

Maximum Ratio Combining (MRC)

Space-Time Block Coding (STBC)

Low-Density Parity Check (LDPC)

Transmit beam-forming (TxBF)

●     Radio 2 – 5 GHz: 2×2 MIMO, two spatial streams

Channels:

●     Radio 2 – 5 GHz: 20 MHz, 40 MHz, 80 MHz, and 160 MHz

Combined peak data rate: 1.733 Gbps

●     Radio 2 – 5 GHz: 6.5 Mbps to 1.733 Gbps (MCS0 to MCS9)

Radio technologies: Orthogonal Frequency-Division Multiplexing (OFDM)

Modulation types: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM

Packet aggregation:

●     Aggregate MAC Protocol Data Unit (A-MPDU)

●     Aggregate MAC Service Data Unit (A-MSDU)

Dynamic Frequency Selection (DFS)

Cyclic Delay/Shift Diversity (CDD/CSD)

Maximum Ratio Combining (MRC)

Space-Time Block Coding (STBC)

Low-Density Parity Check (LDPC)

Transmit beam-forming (TxBF)

●     Radio 1 – 2.4 GHz: 2×2 uplink/downlink MU-MIMO, two spatial streams

●     Radio 2 – 5 GHz: 2×2 uplink/downlink MU-MIMO, two spatial streams

Channels:

●     Radio 1 – 2.4 GHz: 20 MHz and 40 MHz

●     Radio 2 – 5 GHz: 20 MHz, 40 MHz, 80 MHz, and 160 MHz

Combined peak data rate: 2.976 Gbps:

●     Radio 1 – 2.4 GHz: 8.6 Mbps to 0.574 Gbps (MCS0 to MCS11)

●     Radio 2 – 5 GHz: 8.6 Mbps to 2.402 Gbps (MCS0 to MCS11)

Radio technologies: uplink/downlink Orthogonal Frequency-Division Multiple Access (OFDMA)

Modulation types: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM

Packet aggregation:

●     Aggregate MAC Protocol Data Unit (A-MPDU)

●     Aggregate MAC Service Data Unit (A-MSDU)

Dynamic Frequency Selection (DFS)

Cyclic Delay/Shift Diversity (CDD/CSD)

Maximum Ratio Combining (MRC)

Space-Time Block Coding (STBC)

Low-Density Parity Check (LDPC)

Transmit beam-forming (TxBF)

WPA3

●     2.4 GHz: two built-in omnidirectional antennas, the max. antenna gain is 2 dBi.

●     5 GHz: two built-in omnidirectional antennas, the max. antenna gain is 2 dBi.

Bluetooth

●     One integrated vertically polarized omnidirectional antenna, the max. antenna gain is 2 dBi.

Downlink: 4 x 10/100/1000Base-T auto-negotiation RJ45 Ethernet ports

1 x micro USB console port (serial console port)

1 x Bluetooth 5.0

●     AP power-on status

●     Software initialization status and upgrade status

●     Uplink service interface status

●     CAPWAP tunnel timeout

●     Specific AP locating

●     Press the button for shorter than 2 seconds. Then the device restarts.

●      Press the button for longer than 5 seconds. Then the device restores to factory settings.

Shipping: 96 mm x 128 mm x 59 mm (3.78 in. x 5.04 in. x 2.33 in.)

Shipping: 0.31 kg (0.68 lbs)

●     12 V DC/1 A power input over DC connector: The DC connector accepts 2.1 mm/5.5 mm center-positive circular plug. A DC power supply needs to be purchased independently.

●     PoE input over the backplane interface: compliance with 802.3af/at standard (PoE/PoE+)

Note: If both DC power and PoE are available, DC power is preferred.

●     DC power: 10 W

●     802.3at (PoE+): 10 W

●     802.3af (PoE): 10 W

●     Idle mode: 3.5 W

Storage humidity: 5% RH to 95% RH (non-condensing)

Operating temperature: –10°C to +45°C (14°F to 113°F)

Operating humidity: 5% RH to 95% RH (non-condensing)

At an altitude between 3,000 m (9,842.52 ft.) and 5,000 m (16,404.20 ft.), every time the altitude increases by 166 m (546 ft.), the maximum temperature decreases by 1°C (1.8°F).

SPI: 8 MB

Nand: 128 MB

●     Max. transmit power: +21 dBm (126 mW)

●     Minimum transmit power: +8 dBm (6.31 mW)

5 GHz

●     Max. transmit power: +21 dBm (126 mW)

●     Minimum transmit power: +8 dBm (6.31 mW)

Note: The transmit power adjusted in percentage. The transmit power is limited by local regulatory requirements.

Band steering

Each SSID can be configured with the authentication mode, encryption mechanism, and VLAN attributes independently.

Remote Intelligent Perception Technology (RIPT)

Intelligent STA identification technology

Intelligent load balancing based on the STA quantity or traffic

Rate set settings

Radio-based STA limiting

Layer 2 and Layer 3 topology between an AP and an AC

An AP can automatically discover the accessible AC.

An AP can be automatically upgraded through the AC.

An AP can automatically download the configuration file from the AC.

CAPWAP through NAT

MTU setting and fragmentation over CAPWAP tunnels

Encryption over CAPWAP data channels

Encryption over CAPWAP control channels

PSK and web authentication

QR code-based guest authentication, SMS authentication, and MAC address bypass (MAB) authentication

Data encryption: WEP (64/128 bits), WPA (TKIP), WPA-PSK, WPA2 (AES), WPA3-Enterprise, WPA3-Individual

VLAN-based user isolation

User isolation

Rogue AP detection and containment

Time range-based ACL

ACL based on a Layer 2 interface

ACL based on a Layer 3 interface

Ingress ACL based on a wireless interface

Dynamic ACL assignment based on 802.1X authentication (used with the AC)

MAC address table size: 1,024

Max. number of static MAC addresses: 1,024

Max. number of filtered MAC addresses: 1,024

Full-duplex and half-duplex modes of interfaces

IEEE802.1p and IEEE802.1Q

Max. number of VLANs: 4,094

VLAN ID range: 1–4,094

Max. number of ARP entries: 1,024

ARP check

Max. number of IPv4 addresses configured on each Layer 3 interface: 200

NAT, FTP ALG and DNS ALG

IPv6 DHCP client

Max. number of static IPv4 routes: 1,024

Max. number of static IPv6 routes: 1,000

IPsec VPN

SNTP client

SNMPv1/v2c/v3

Fault detection and alarm

Information statistics and logging

When the AP works in Fat mode, it can be switched to Fit mode through the console port or Telnet mode.

When the AP works in cloud mode, it can be managed through Ruijie Cloud.

Measuring users’ network experience based on indicators such as the latency, packet loss, signal strength, and channel utilization, and visualizing results of the network experience

Statistics on the number of online and offline failures of STAs associated with different APs, average signal strength, and other parameters

VIP monitoring and alarm, and custom alarm thresholds

STA global experience map and experience coverage evaluation based on the time range

STA access protocol replay and fine-grained STA fault diagnosis

Note: To support the preceding functions, ensure that the AP works in Fit mode.

Client steering to cope with roaming stickiness, and experience indicator comparison

Client steering to cope with remote association, and experience indicator comparison

One-click diagnosis – analyzing problems and providing suggestions

Time capsule – analyzing the device version and configuration change history

Deployment through Zero Touch Provisioning (ZTP) – creating configuration templates and automatically applying configured templates

One-click discovery of the wired and wireless network topology and topology generation

Authentication implemented in the cloud, without the need to deploy the local authentication server

Granting operation permissions to administrators in different scenarios